We use own and extern cookies to offer you the best experience and service. If you surfing our website, you accept that we use them. You can change your cookies preferences at any time. More information about cookies policy
español frances ingles portugues
Always, the best prices
LOCURA DIGITAL
Radio communication leader
Call us [+34] 938.616.372. Hours Mon.-Thur. 9:00h - 14:00h & 15:00h - 18:30h. Fri. 9:00h - 15:00h.
28/03/2024, 29/03/2024 & 01/04/2024 CLOSED

KENWOOD TS-590S. HF / 50 MHz all mode transceiver

KENWOOD TS-590S. High-performance HF / 50 MHz all mode transceiver more Manufacturer: kenwood Reference TS590S EAN 019048190796

discontinued
Before 1633.50€

KENWOOD TS-590S

The TS-590S marks a bold new chapter in Kenwood’s proud history of high-performance HF transceivers. Featuring a narrow-band Roofing Filter, it significantly reduces interference from unwanted signals, resulting in excellent RX performance and revealing signals that would be hidden to lesser rigs.

With IF AGC based on advanced DSP technology, Kenwood has essentially redefined HF performance.
Built to satisfy the most demanding DX’er, this high-performance HF transceiver takes Amateur Radio to the next level and continues the Kenwood tradition of operating ease and rugged reliability.

The price only includes the Kenwood TS-590S transceiver.

KENWOOD TS-590S

KENWOOD TS-590S

KENWOOD TS-590S

KENWOOD TS-590S

KENWOOD TS-590S

KENWOOD TS-590S

KENWOOD TS-590S

KENWOOD TS-590S

Features

Superb benefits on RX: Excellent Dynamic Range
Thanks to the narrow band Roofing filter from the first mixer, this new transceiver provides the best dynamic range of its class to handle adjacent unwanted signals.


Powerful 500 Hz/2.7 kHz Roofing filter

In the 15, 20, 40, 80 or 160 meters bands, the TS-590SG uses a lower conversion for the first IF (11.374MHz). Counting with the first directly Roofing filter (6 kHz bandwidth) after the mixer to improve noise reduction ability for adjacent signals outside our frequency.

ts-590

What really determines the RX benefits is the second Roofing filter, after amplifying. The TS-590SG is equipped with 500Hz and 2.7kHz MCF 6 pole filters. Achieving with that a superb dynamic range when there are adjacent signals, a feature that was not possible when using a higher conversion. When the interfering signal was close to working signal, a virtual plane dynamic range is maintained. With strong interfering signals, the capture of the signal is clear.
Note: For Amateur bands 1.8 / 3.5 / 7 / 14 / 21 MHz, with reception modes CW / FSK / SSB the lower conversion is automatically selected if the passing band is 2.7 kHz or lower.

ts590

DDS generates excellent feature of signal to noise ratio, significantly reducing the noise generated by adjacent unwanted signals.

For the first local oscillator, instead of using the conventional PLL / VCO, the DDS (Direct Digital Synthesizer) output is directly supplied to the mixer. When lower conversion is activated, the oscillator frequency is lower than if a superior conversion is used, the output has a better feature of signal to noise ratio and an optimal level of reciprocal mixture.

Wide range of facilities thanks to the 32-bit floating point DSP.

In addition to basic functions such as AGC, Digital IF filters, detection and demodulation, a large number of facilities including noise reduction and IF rejections are all implemented by last generation algorithms.


AGC advanced digital signal processor from the IF level.

The TS-590SG uses a DSP from the IF level. Kenwood was the first brand offering IF AGC based on DSP in amateur equipments (TS-870) and the DSP technology has been improved in the TS-590SG, resulting in the development of an excellent IF AGC. It is possible to reach an optimal level of AGC signals even beyond the Roofing Filter and the IF passing band. You can be sure to optimally operate at any time, without having to think about the Roofing Filter bandwidth. The Gain control performance has been totally improved for the desired signal in the IF passing band (RX Band). The result is a characteristic of IMD (Intermodulation Distortion) hand in hand with the high end transceivers. Enjoy a superb RX with next-generation Kenwood sound.
ts590


ts590

Adjustable IF filter passband

This operates as the passband HI CUT/LO CUT function in SSB/AM/FM modes, and as the WIDTH/SHIFT control function in CW/FSK/SSB-DATA modes. Operation can be switched using the menu in SSB and SSB-DATA modes.

ts590

IF Notch

Remove a powerful interfering signal with a notch filter to capture a weak target signal. Choose from automatically variable notch frequency in IF Auto-Notch(1) and manually adjustable notch frequency in Manual Notch(2) depending on your interference situation.
(1): Available only in SSB mode
(2): Available in SSB/CW/FSK modes


IF Filter

One-touch A/B switching FIL A/B can be set independently with VFO A/B. This convenient function enables swift operation during contests or split operation.


Digital/Analogue Noise Blanking (NB1 / NB2)

In addition to the analogue noise blanker (NB1), which has a proven track record for eliminating weak noise, this transceiver is equipped with a digital noise blanker (NB2). The optimum blanker for the type of noise and reception conditions can be selected. NB1 enables stable noise suppression independent of reception bandwidth, while NB2 is effective against noise that defies tracking by an analogue noise blanker.


DSP Noise Reduction (NR1 / NR2) ts590
This series features two kinds of noise reduction methods: NR1 and NR2. NR1 applies the most optimum kind of noise reduction for each reception mode, while NR2 employs the SPAC method, which is more effective for CW operation.

NR1
Spectral-subtraction noise reduction has been developed with a focus on improving reception clarity for weak SSB signals. It enables the bringing to the surface of a target signal that is swamped by noise, without any loss in sound quality. For non-speech modes (CW/FSK), a line enhancer offers tried and true noise reduction.

ts590 NR2
NR2 is SPAC-based noise reduction that is effective for CW operation as it can suppress noise at the same frequency as the target signal (not available for FM mode).




Highly reliable design guarantees stable operation

Heavy-duty design

A pair of 60mm×60mm fans have been used for the cooling system, which provides sufficient air flow at low rpm for less noise. Attention has been paid not only to the fans and motors but also to the size and shape of the intake/exhaust vents as a comprehensive approach to quieter operation. ts590 The aluminum die-cast chassis is combined with a large heat sink to effectively dissipate heat, minimising the rise in temperature in the final section during continuous transmission sessions. This heavy-duty design is capable of withstanding grueling conditions typical of contests or long hours of hard operation.



Built-in high-speed automatic antenna tuner ts590

The built-in preset-type automatic antenna tuner covers amateur bands in the 160~6m band range and can operate when the transceiver is receiving. High-speed operation and the proven relay method enable rapid QSY through instantaneous band changing.








Drive output (including 135 kHz band)

The transceiver comes equipped with a drive output (DRV) connector that enables external access to the transmission drive output (approx. 0 dBm). This is not just convenient when a transverter is attached; this DRV connector can also be put to use for transmission on the 135 kHz band, for which the main antenna terminal cannot be used. Performance can be further enhanced when combined with a dedicated reception antenna connector.

Speech processor (SSB/AM/FM)

The speech processor increases the clarity of messages for the receiving station by raising average transmission modulation. Besides adjusting compression level, soft and hard modes are available for 2-level adjustment. Compression levels can be set for each of mic transmission and voice-message transmission.


Band-adjustable TX filter (SSB/AM)

The TX filter passband is switchable. Low-pass and high-pass cut-offs can be switched independently for fine control over filter operation.


TX equaliser (SSB/AM/FM for each mode)

The equaliser enables the adjustment of frequency characteristics to suit the voice quality and microphone characteristics on the transmitting end. Users can choose from flat (default), high boost (2 types), Formant pass, and bass boost (2 types), as well as conventional and user settings (using the ARCP-590G).


TX monitor

The transmission monitor function outputs transmission audio via the speaker in 20 steps, allowing you to check sound quality.


Other TX features

- VOX function (adjustable gain, selectable delay time)

- Adjustable TX power output

- Adjustable MIC gain

- Adjustable CAR level





ts590

Diverse functions supporting CW operation.

CW auto-tune
You can automatically zero-in on a target signal during reception in CW operation with just the press of a button. This function will also tune in to the RIT frequency during RIT operation.


2 key terminals on rear panel
An electronic keyer (built-in) paddle terminal and a separate terminal for an external keyer have been included. PC keying is possible even when a paddle is connected.


Other CW features
Support for full break-in and semi break-in (semi break-in delay time: 50ms~1000ms) Pitch control (300~1000Hz) Side tone monitor with 20-step volume control Electronic keyer (selectable key speed, A/B modes) Memory keyer (max. 4-channel message memory) Microphone paddle mode CW reverse mode CW auto transmit function, in which a simple key-press will switch automatically to CW in SSB mode


The large display


LED backlight with selectable colour tone.
The large display ensures outstanding visibility under all conditions. In addition to conventional amber and green, you can now select intermediate colours and change from amber to green in 10 steps.




A variety of functions for easy operation


New Split function enabling quick setting "Direct frequency entry, Direct band selection" ts590

In addition to conventional split frequency setting methods, the TS-990's proven split setting functionality has been included. A long press of the SPLIT key, when making a 2kHz up setting, will enable quick setting by pressing "2" on the keypad. Furthermore, in simplex operation with just XIT on, the XIT frequency can be changed with TF-SET. The keypad keys are now band-direct keys. Each band has 3 memories, enabling quick call-up of usually-used frequencies.


PC control through USB connectivity

PC control of the transceiver and transceiver audio transmission have been made possible through a USB cable with the inclusion of a dedicated PC-control USB connection terminal. ts590

Note: Delays may occur when using USB audio. We recommend using USB audio in situations where time lag is not an issue.

Remote control of the TS-590SG via computer

Using the ARCP-590G (radio control program), virtually all functions can be controlled via a computer. Changing various function settings and managing memory channels can all be done from your PC. The ARCP-590G also enables the recording and erasure of voice messages.



Voice guide and recording functions (option) ts590

VGS-1:Voice guide and storage unit enables voice guidance for frequency, key operation, settings, etc., and recording/playback of messages. A Manual Mode, in which vocalization takes place only when buttons are pressed, has been added to the voice guidance. Either English or Japanese can be selected for the voice guidance language.
-Voice memory: max. 4 channels (recording time: 30 seconds each for CH1 & CH2, 15 seconds each for CH3 & CH4)

-Constant receiver recording: 30 seconds. (1 channel)


Memory/Scan functions

Easy-to-use, diverse memory functions

The transceiver features a memory that can store up to 120*1 frequency memory channels, with each able to be given a memory name of up to 8 letters. Also included are the memory scroll function, which can be used to check memory data without changing operating frequency, memory channel copy, which enables the copying of memory data to another channel, single channel memory clear, memory lockout, memory shift, and the ability to change memory data/frequency temporarily. Other features include the Quick Memory function, which can store up to 10 channels*2 on the fly, and the capacity for temporary changes to memory shift and memory data.

*1: Including specified range memory and expanded memory channels.

*2: 3, 5 or 10 channels can be selected.

ts590




Multiple scan functions

Program scan, memory scan, group scan, subtone scan and CTCSS scan are included among the many scan functions available. The transceiver also offers program slow scan, which automatically reduces the scanning speed around any frequency of special interest.

KENWOOD SKY COMMAND SYSTEM II

Enables full-duplex operation with improved functionality such as visual confirmation of HF frequency on the LCD panel. Control via TNC (AX.25) enables more access to HF functions: XIT, mode switching, split-frequency operations on/off, memory shift, and frequency step selection. The transporter sends out its pre-programmed call sign via CW every 10 minutes.

Notes:
- KENWOOD SKY COMMAND SYSTEM II uses a pair of TH-D72E/ TM-D710E/TM-D710GE transceivers.
- Refer to applicable amateur radio regulations to check whether you are permitted to use this function.

KENWOOD TS590S

Other features

RX:
- ATT, pre-amp

- RF gain adjust

- AF gain

- SQL level set

FSK:
- Basic RTTY operation settings (keying polarity, shift width, high/low tones, reverse mode)

FM:
- FM Wide/Narrow switching for transmission/reception

- Repeater subtone

- FM signalling (CTCSS, cross-tone)

DATA:
- SSB-DATA/FM-DATA/AM-DATA transmission mode-compatible. Transmission output settings and transmission sound source (front/rear) selectable for data transmission.

- Variable DATA modulation/demodulation level

- Selectable DATA modulation line (ACC2/USB)

- DATA VOX

Accessory connectors:

- ACC2 connector for DATA communication

- Remote connector compatible with linear amp control (built-in vacuum tube linear amp control relay, selectable transmission attack delay)
External connectivity:

- Compatible with external antenna tuner (AT-300*)

- DX Packet Cluster tune (when connected to TM-D710E/TM-D710GE/TH-D72E)

Other:

- Power-on message (message of up to 8 alphanumeric characters can be input for display when power is switched on)

- Split data transfer using COM port

- Firmware updates

- Adjustable long-keypress timing

Accessories 1/2