ARESBLACK. 27 Mhz CB radio model ARES BLACK LAFAYETTE mark. AM

LAFAYETTE ARES BLACK EMISORA CB 27 MHZ COLOR NEGRO AUTO CARAVANAS 64408
  • LAFAYETTE ARES BLACK EMISORA CB 27 MHZ COLOR NEGRO AUTO CARAVANAS 64408
  •  64408
  •  64408
  •  64408
  •  64408
  •  64408
  •  64408
  •  64408
  •  64408
Available product.
  • ARESBLACKCARAVANAS
  • ARESBLACK. 27 Mhz CB radio model ARES BLACK LAFAYETTE mark. AM / FM 4 watts. Color BLACK. ...

    More info

  • 95,00€
  • VAT not included

We're working in our new page, i'ts possible that you discover some mistakes.

In that case, you can notify us

clicking HERE..

Contents of kit

Front view of the station LAFAYETTE

Rear view of the station

Measures




Thank you for purchasing a product LAFAYETTE.

To take full advantage of this product, please read carefully the instructions for use that you will find.

ATTENTION:

Do not try to cast if the antenna has not previously been connected, this action could seriously damage your computer.

This equipment has been tested and calibrated at the factory, not open or manipulate their internal components.

CONNECTING THE ANTENNA:

The cable connecting the antenna must end in a PL-259 connector to allow connection to the computer. Use only the antennas adjusted banda 27 MHz. And cable RG-58 / U with a typical impedance of 50 Ohms.

STAND MICROPHONE:

Install the microphone stand in a comfortable position inside the vehicle, verify that both the cable and the microphone does not interfere or harm the operations of driving.

Interference caused by the distribution system in your vehicle:

CONTROL OF CONTROLS AND INDICATORS:

1 - Microphone connector 4-pin
2 - On / Off and volume control
3 - Control of "Squelch"
4 - LCD
5 - Selector banda AM / FM
6 - Scanner
7 - Channel 9 (reset)
8 - Selected channel, upload / download

Modern vehicles do not generally cause interference problems due to their distribution systems or boot, so the station should not suffer any interference caused by engine operation.

DISPLAY AND OPERATION OF THE ISSUING ARES:

Having successfully installed the radio, connect your antenna and CB made the connection to food approach in the following 6 steps to a correct and successful use of the device.

Step 1: Connect the microphone to the attachment at the front of the device and verify their proper and safe connection.

Step 2: Verify that the connection of the antenna connector of the station is properly done.

Step 3: Verify that the control of "Squelch" is pointing to the time position "9" o'clock.

Step 4: Turn the device with the same control and adjust the volume level more satisfactory.

Step 5: Select the desired channel using the channel selector: up / down.

Step 6: To transmit, press the "PTT" on the microphone. To receive and hold the "PTT".

CONTROLS AND CONNECTORS: FUNCTIONS AND USES

1 - ON / OFF On / Off and volume control

This triggers the control device and can adjust the sound volume to receive more satisfactory.

2 - Control "Squelch"

Turn this control clockwise to mute the device when not receiving a clear signal and I can hear noise, I get a quieter and more comfortable status "standby".

3 - Selector AM / FM

Press this button to select AM or FM.

4 - SCAN Button

Their equipment includes the role of CB scanner channel. This feature allows you to move through the 40 channels and stop on the channel that is occupied and will remain on that channel for about 7 seconds after the conversation detected, then resume again scanning channels. To activate this function press the "SCAN", the display indicated the operation. If you would like to end action scan, press the button again "SCAN" or the "PTT" button on the microphone, this ends the "scanner".

5 - Button CHANNEL 9 / RESET

Tighten this button in case of emergency, this will lead to Channel 9 for immediate (emergency channel). This button can also be used as "RESET" when the station is not functioning properly. Hold this button while turning the radio to reset the device (reset). By doing this, the display will show the letters "RS" and the station will reset the original factory settings.

6 - UP channel selector (up) / DOWN (down)

Press the buttons "UP" or "DOWN" to select the desired channel. When these buttons are pressed quickly change channels up or down depending on which button you select.

7 - power cord

Connect the power cable to the vehicle battery (red wire to positive 13.8 volts, and black wire to ground) or power (in the same manner as in the battery.) Pay close attention to this step, a wrong connection (reverse polarity) or a higher voltage supply to 13.8 volts to damage the equipment.

External speaker

The station has connector on the back for connecting external speaker plug type "jack" of 3.5 mm.