ARESBLACK. CB 27 Mhz mark Issuer LAFAYETTE BLACK ARES model. AM

ARESBLACK. Emisora CB 27 Mhz marca LAFAYETTE modelo ARES BLACK. AM/FM 4 Watios. Color NEGRO. + ANTENA SLIM 145 + BASE IMAN MIRMIDON BM150 65019
  • ARESBLACK. Emisora CB 27 Mhz marca LAFAYETTE modelo ARES BLACK. AM/FM 4 Watios. Color NEGRO. + ANTENA SLIM 145 + BASE IMAN MIRMIDON BM150 65019
  •  65019
  •  65019
  •  65019
  •  65019
  •  65019
  •  65019
  •  65019
  •  65019
Not available product.
  • ARESBLACKITB
  • ARESBLACK. CB 27 Mhz mark Issuer LAFAYETTE BLACK ARES model. AM / FM 4 watts. Color BLACK. ...

    More info

  • 75,00€
  • VAT not included

 

Kit Contents

 

Front views of the station LAFAYETTE

 

Rear view of the station

 

Measures



 

 

Thank you for purchasing a product LAFAYETTE.

 

To take full advantage of this product, please read the instructions that we give details below.

 

ATTENTION:

? Do not attempt to deliver if the antenna has not been previously connected, this action could seriously damage your computer.

· This equipment has been calibrated and tested at the factory, do not open or tamper with internal components.

 

 

CONNECTING THE ANTENNA:

The cable connecting the antenna must end in a PL-259 connector to allow connection to the computer. Use only antennas adjusted in the range of 27 Mhz. And cable RG-58 / U with a typical impedance of 50 ohms.

 

MICROPHONE STAND:

Install the microphone stand in a comfortable position inside the vehicle, make sure that both the cable as the microphone does not harm or interfere with driving operations.

 

 

INTERFERENCE CAUSED BY THE SYSTEM OF DISTRIBUTION OF YOUR VEHICLE:

CONTROL CONTROLS AND INDICATORS:

1 - Microphone connector 4 pin
2 - On / Off and volume control
3 - Control of "squelch"
4 - LCD Screen
5 - Electric Band AM / FM
6 - Scanner
7 - Channel 9 (reset)
8 - Channel selection, up / down

Modern vehicles do not usually cause interference problems due to their distribution systems or boot, so the station should not suffer any interference caused by engine operation.

DISPLAY AND OPERATION OF THE ISSUER ARES:

 

After you have successfully installed the station correctly connected CB antenna and the connection to the power based on the following six steps for proper and successful use of the device.

 

Step 1: Connect the microphone to the connector on the front of the unit and verify correct and safe connection.

Step 2: Verify that the connection of the antenna connector on the transmitter is properly done.

Step 3: Verify that the control of "Squelch" is in indicating the time position "9" o'clock.

Step 4: Turn on the device with the same control to adjust the volume level more satisfying.

Step 5: Select the desired channel by channel selector up / down.

Step 6: To transmit, press the "PTT" button on the microphone. For release the "PTT".

 

 

CONTROLS AND CONNECTORS: FUNCTIONS AND USES

 

1 - ON / OFF On / Off and volume control

This triggers the control unit and to adjust the sound volume to receive more satisfactory.

 

2 - Control "SQUELCH"

Turn this control clockwise to mute the device when not receiving a clear signal and just listen to noise, this will achieve a quiet and comfortable condition standby.

 

3 - Selector AM / FM

Press this button to select AM or FM.

 

4 - SCAN Button

Their equipment includes the function of CB "Scanner" channel. This feature allows you to scroll through 40 channels and stop on the channel're busy and will remain on that channel for about 7 seconds after the end of the conversation detected, then resume again the channel scan. To activate this feature press the "SCAN", the display will indicate the operation. If you would like to complete the action of scanning, press the button again "SCAN" button or "PTT" button on the microphone, this ends the "Scanner".

5 - Button CANAL 9 / RESET

Press this button in case of emergency, this will lead to Channel 9 immediately (emergency channel). This button can also be used as "RESET" when the station does not work properly. Hold this button while turn on the radio to reset the device (reset). By taking this action, the display will show the letters "RS" and the station is reset to the initial factory settings.

 

6 - Channel selector UP (up) / DOWN (down)

Press the "UP" or "DOWN" to select the desired channel. When these buttons are pressed quickly change channels up or down depending on which button you choose.

 

7 - Power Connection Cable

Connect the power cable to the vehicle battery (red wire to positive 13.8 volts and black wire to ground) or power supply (in the same way as in the battery.) Pay close attention to this step, a wrong connection (reverse polarity) or a higher voltage power supply to 13.8 volts will damage the equipment.

 

External Speaker

The station has connector on the back for connecting external speaker with plug type jack 3.5 mm.